1 of 1

Access Debug-logs

This guide describes the procedure to get access to the debug logs

Requirements

The following tools are required to get access to the debug logs:

Linux based host system with minicom installed
- use sudo apt-get install minicom to install
USB to UART adapter
UART cable to connect to the carrierboard

Hardware connection

At first you have to connect your UART cable to the Jetson the following way

Signal Jetson

Signal UART adapter

note

Carrierboard

Connection

Now connect the cable to the USB to UART adapter und connect the USB to your Computer

Software

The following steps have to be done on your linux host system

Install minicom

In case you do not have Minicom already installed use the following command to install it:

install minicom

sudo apt-get install minicom

The following command makes sure that the USB to UART adapter is properly recognized by the linux system.

Check tty device

check tty device

ls /dev | grep ttyUSB

Please check your hardware connection to the USB to UART adapter, If the command does not print ttyUSB0 back to the terminal.

Open minicom

Now everything is set up get the debug logs, you just have to start minicom with the following parameters:

start minicom

sudo minicom -D /dev/ttyUSB0

Your terminal should now look like something like this

Welcome to minicom 2.7.1

OPTIONS: I18n 
Compiled on Aug 13 2017, 15:25:34.
Port /dev/ttyUSB0

Press CTRL-A Z for help on special keys

Start Jetson

Now connect your Jetson to the powersupply and start it properly. The minicom terminal should print a lot of messages during the boot of the Jetson system ending with a login window to the Linux system.

Welcome to minicom 2.7.1

OPTIONS: I18n 
Compiled on Aug 13 2017, 15:25:34.
Port /dev/ttyUSB0, 11:47:06

Press CTRL-A Z for help on special keys

��
[0000.025] W> RATCHET: MB1 binary ratchet value 4 is too large than ratchet level 2 from HW fuses.
[0000.034] I> MB1 (prd-version: 1.5.1.7-t194-41334769-98030a79)
[0000.039] I> Boot-mode: Coldboot
[0000.042] I> Chip revision : A02P
[0000.045] I> Bootrom patch version : 15 (correctly patched)
[0000.050] I> ATE fuse revision : 0x200
[0000.054] I> Ram repair fuse : 0x0
[0000.057] I> Ram Code : 0x1
[0000.059] I> rst_source : 0x0
[0000.062] I> rst_level : 0x0
[0000.065] I> Boot-device: QSPI
[0000.068] I> Qspi flash params source = brbct
[0000.072] I> Qspi using bpmp-dma
[0000.075] I> Qspi clock source : pllp
[0000.079] I> QSPI Flash Size = 64 MB
[0000.082] I> Qspi initialized successfully
[0000.086] W> No valid slot number is found in scratch register
[0000.092] W> Return default slot: _a
[0000.095] I> Active Boot chain : 0
[0000.098] I> Boot-device: QSPI
[0000.101] I> Qspi flash params source = brbct
[0000.107] W> MB1_PLATFORM_CONFIG: device prod data is empty in MB1 BCT.
[0000.114] I> Temperature = 23500
[0000.117] W> Skipping boost for clk: BPMP_CPU_NIC
[0000.122] W> Skipping boost for clk: BPMP_APB
[0000.126] W> Skipping boost for clk: AXI_CBB
[0000.130] W> Skipping boost for clk: AON_CPU_NIC
[0000.134] W> Skipping boost for clk: CAN1
[0000.138] W> Skipping boost for clk: CAN2
[0000.142] I> Boot-device: QSPI
[0000.145] I> Boot-device: QSPI
[0000.148] I> Qspi flash params source = mb1bct
[0000.152] I> Qspi using bpmp-dma
[0000.155] I> Qspi clock source : pllc_out0
[0000.158] I> Qspi reinitialized
[0000.161] I> Qspi flash params source = mb1bct
[0000.167] I> Qspi flash params source = mb1bct
[0000.172] I> ECC region[0]: Start:0x80000000, End:0x780000000
[0000.177] I> ECC region[1]: Start:0x0, End:0x0
...