| SKU | Description |
|---|---|
Auvidea can take no responsibility for the accuracy or completeness of any information presented in an exported PDF document as the export feature is developed, managed and maintained by GitBook. Those export mechanisms are subject to change without interaction by Auvidea. Please note that Auvidea includes this version table to identify the document and reference changes.
Flexible design and manufacturing
designed and manufactured in Germany
in-house fully automated production line with 3D AOI
special configuration possible with minimum purchase of 25 pcs (display port, M.2, PoE, 48V power in, super cap option, 2 RPi camera module connectors, SPI, I2C, switches, etc.)
design services: you architect your custom carrier board and Auvidea designs and produces it, please ask for a quote.
| Version | Changes |
|---|---|
| Version | Changes |
|---|---|
| Description | JNX30 | JNX30-LC | JNX30-LC-PD | JNX30-PD | JNX30-PSE |
|---|---|---|---|---|---|
| Top side | Bottom side | |
|---|---|---|
| Description | Note | |
|---|---|---|
| Description | JNX30 series |
|---|---|
1.3
Starting document JNX30-LC
1.4
Combination of JNX30 and JNX30-LC Manual and other versions of JNX30
1.5
Updated Appendix
1.6
Added Appendix D
1.7
Ported Manual to Gitbook
38401-2
added 5V 8A power supply
added PCIe connector (rotate it compared to rev 1)
added CAN connector (requires external CAN transceiver module - 38163-3)
added mount pins of power in connector to GND
added another 220uF Tantal cap on bottom side
38401-3
changed MCU footprint from TSSOP-20 to UFQFN-28
supports STM32F042G6U6 and STM32L031G6U6 - dual rail power
added support for MCU flashing from Jetson via UART
changed R110 to 3.01k for maximum input current of 6A
changed main power supply from LT8646 to MIC28514
changed magnetics to XAL1010-103 with 14.8 mOhm DCR => better efficiency
extended e-fuse support for TPS26630/1 type - added two resistors
added 2nd FAN connector so that the FAN cable connection does not require an extension cable
38401-4
not released
38401-5
changed 8A power supply to 12A
changed 3.3V power supply and power it by 12V
changed MCU LDO (absolute max. input voltage 26V - if populated)
added discrete components for power up (no MCU)
moved FAN connector for better access
changed reverse voltage protection to MOSFET
changed over-current protection to fuse
version with 5V 8A power controller (derived from 38401-4.1)
changed back to input diode (for PoE PD support
Power
6V - 19V
6V - 19V
NX powering
5V 8A
5V 8A
Display Port
no
no
HDMI
yes
yes
Fan connector
yes
yes
M.2 NVME Key M
yes
yes
Micro SD card
yes
no
M.2 Key E
optional
optional
CAN RX / TX
yes
no
USB 3
1x USB 3.1
1x USB 3.1
Micro USB
1x, host & device mode
1x, device mode
Auto Flashing
yes
yes
USB 2.0 (JST-GH)
1x
1x
Gigabit Ethernet, RJ45
1x
1x
PoE option
yes
no
CSI-2
2x
2x
UART
2x (J14) 1x (GPIO)
2x
I2C
2x (GPIO)
no
I2S (5V tolerant, unidirectional)
1x (GPIO)
no
SPI (5V tolerant, unidirectional)
2x (GPIO)
no
Overvoltprotection with TVS diode
yes
yes
Unidirectional level shifters
yes
no
Buttons
8 pin header
no
Power in converter
yes
no
Expandability:
USB and Ethernet module
(optional)
(optional)
(optional)
(optional)
(optional)
IMU module
(optional)
(optional)
(optional)
(optional)
(optional)
EEPROM and crypto chip (for SW copy protection) module
(optional)
(optional)
(optional)
(optional)
(optional)
PCIe x1 connector module
(optional)
(optional)
(optional)
(optional)
(optional)
LM823 WIFI module
(optional)
(optional)
(optional)
(optional)
(optional)
2x CSI-2 interfaces module
(optional)
(optional)
(optional)
(optional)
(optional)
Micro SD card module
(optional)
(optional)
(optional)
(optional)
(optional)
RTC battery module
(optional)
(optional)
(optional)
(optional)
(optional)
Over current fuse module
(optional)
(optional)
(optional)
(optional)
(optional)
UPS option for graceful power down module
(optional)
(optional)
(optional)
(optional)
(optional)
On board MCU for watchdog and remote power cycle (LTE) module
(optional)
(optional)
(optional)
(optional)
(optional)
HDMI
standard HDMI connector (2.0)
USB 3.0/3.1
5Gb/s (dependent on compute module)
Physical size
80 x 104.6mm
Mounting holes
4x M3
Temperature range
0 to 70°C (extended temperature range optional)
Humidity
noncondensing
Longevity
Very long as no temperature sensitive components are used (like electrolytic capacitors)
Carrier board logic
< 1 watt
3.3/5V power converter efficiency
> 90%
Power in converter efficiency
>90%
JNX30
JNX30-LC
JNX30-LC-PD
JNX30-PD
JNX30-PSE
JNX30-PDiso
70796
low cost (LC)
70804
low cost (LC), power device (PD)
70802-PD
power device (PD)
70802-PSE
power sourcing equipment (PSE)
70898
power device (PD), isolated (ISO)
