JN30D Overview
Overview of the product line JN30D for NVIDIA Jetson Nano & TX2 NX & Xavier NX
Last updated
Was this helpful?
Overview of the product line JN30D for NVIDIA Jetson Nano & TX2 NX & Xavier NX
Last updated
Was this helpful?
70876
Standard version
70876-WSD
Without SD Card slot
1.0
Initial document, internal verification process
1.1
Internal verification process
1.2
Updated contents, new pictures
1.3
Added Appendix E & D
1.4
Corrected information in the features and comparison list
1.5
Ported Manual to Gitbook
Auvidea can take no responsibility for the accuracy or completeness of any information presented in an exported PDF document as the export feature is developed, managed and maintained by GitBook. Those export mechanisms are subject to change without interaction by Auvidea. Please note that Auvidea includes this version table to identify the document and reference changes.
38488-1, -2
Engineering prototype
38488-3
Production release
This new JN30D carrier board has been designed primarily for the Jetson Nano compute modules.
When using other modules like the Jetson NX power limits may be exceeded as the USB-C power supply only supplies up to 3A. More power may be supplied to the board via the two 5V pins on the GPIO header. The JN30D may be powered alternatively by the 5V pin on the 10 pin GPIO header. Please make sure that you only connect one power source: USB-C cable or 5V cable. Both are directly connected on the PCB of the JN30D.
Easy integration into passively cooled systems
Optionally available as complete system in passively cooled enclosure
Easy flashing: just connect a USB OTG cable (Auto Flash)
High performance storage: M.2 NVMe PCIe x4
Power
5V 3A (USB C)
5V – 19V
Compatible Modules
Jetson Nano
Jetson Nano
Display Port
-
yes
HDMI
yes
yes
Fan connector
yes
yes
M.2 NVME Key M
yes (x4 PCIe)
-
M.2 Key E
with external module (using J8)
yes
Micro SD card
(optional)
-
CAN RX / TX
(optional)
yes
USB 3.0
1x USB Typ A (native)
4x USB Typ A (USB hub - shared)
USB 2.0
1x USB C
1x JST-GH (J8)
1x Micro USB (device mode only)
Auto Flashing
yes (USB C)
-
Ethernet
Gigabit RJ45 (one LED)
Gigabit RJ45 (2 LEDs)
PoE option
yes (P11)
yes
CSI
2x CSI-2 (4 lanes) plus camera LED
(hardware sync available)
2x CSI-2
UART
2x (J14 and 40 pin GPIO header)
2x (40 pin header)
I2C
2x (40 pin header)
2x (40 pin header)
I2S
1x (40 pin header)
(5V tolerant, unidirectional)
1x (40 pin header)
SPI
2x (40 pin header)
(5V tolerant, unidirectional)
2x (40 pin header)
GPIO
3x in + 3x out (40 pin header)
(5V tolerant, unidirectional)
6x bi dir (40 pin header)
Size
105 mm x 82 mm
69 mm x 45 mm
Overvoltage protection (TVS diode)
Uni-directional level shifters (more reliable than bidirectional)
HDMI
standard HDMI connector (2.0)
USB 3
5Gb/s or 10Gb/s
Physical size
105 mm x 82 mm
Mounting holes
4x M3
Temperature range
0 to 70°C (extended range optional)
Humidity
noncondensing
Longevity
no temperature sensitive components (like electrolytic capacitors)
Carrier board logic
< 1 watt
3.3V power converter efficiency
> 90%
Fully populated variants available
Add-on boards for more USB and Ethernet
IMU
board EEPROM and crypto chip (for SW copy protection)
PCIe x1 connector
LM823 WIFI module
More CSI-2 interfaces (2x4 Lanes, 2x2 lanes)
RTC battery (rechargeable)
Over current fuse (product safety)
UPS option for graceful power down
On-board MCU for watchdog and remote power cycle (LTE)
